Liste des documents
Implémentation Des Algorithmes de Traitement du Signal sur carte FPGA
The aim of this work is to realize an on-board system allowing to automate the control in NDT by ultrasonic. For this, we performed the transmission and reception of signals using an FPGA card that acquisition and signal processing are implemented on the same FPGA circuit. Voir les détails
Mots clés : Non-destructive testing (CND), ultrasonic signals, FPGA, Signal processing
Elaboration et caractérisation des nanoparticules a base de chlorure d’étain SnCl2 et l’application d’élimination de colorants par adsorption
Nanoparticles (NPs) have received considerable attention in recent years due to their unique physicochemical and optoelectronic properties and their applications in various sectors of chemistry, environment, medicine, agriculture and electronics. This dissertation will focus on three main parts, after an introduction to nanotechnologies: a bibliographic study on everything related to nanoparticles, their types, their synthesis methods, their characterizations, their properties and their applications. In the second part we have cited all the experiments of elaboration of our samples of nanoparticles (based on tin chloride) using the method of Co-precipitation so that at the end we have chosen the one that gives the best result to use it in the application of removal of methyl blue dye by adsorption. The third part shows that the results of our samples are excellent and from there we concluded that the nanoparticles (tin ferrites) and thanks to their magnetic behavior they allow to eliminate easily the methyl blue dye by magnetic field. Voir les détails
Mots clés : Nanoparticles (NPs), Magnetic field
Effet du traitement de vieillissement sur l’évolution microstructurale et le comportement électrochimique des aciers inoxydables 2101, 2205 et 2507.
this work, the effect of ageing treatment on the microstructural evolution, morphology and potential distribution of LDX2101, SDX2205 and SDSS 2507 stainless steels is investigated. The heat treatment is carried out in two stages: solution treatment for one hour, then water quenching followed by ageing at 750°C for 2101 and 850°C for 2205 and 2507, for 24 hours holding time. Metallographical characterization is conducted using optical microscopy and scanning electron microscopy (SEM) as well as XRD analysis to identify the phases and precipitates formed after treatment. In order to study the effect of ageing on the morphological changes, magnetic behavior and potential distribution on the surfaces of the treated steels, different modes of atomic force microscopy (AFM) are used. The results showed a clear increase in roughness with a very heterogeneous potential distribution due to microstructural changes as a result of the formation of precipitates and secondary phases Voir les détails
Mots clés : LDX2101, SDX2205, SDSS 2507 stainless steels, The heat treatment
Caractérisation des écoulements en micro fluide par vélocimétrie à l’échelle micron appliquée aux microsystèmes
Microfluidics has been a field of research in full expansion for ten years, whose vitality is nourished by the diversity of its applications Today, new technologies indeed make it possible to manufacture electromechanical systems of micro and nanometric size, up to 'at significant levels of complexity, and equipped with all kinds of functionalities. These new possibilities have been used in aspectacular way for many applications, such as DNA microarrays, or lab-onchip. In all these systems, the problem of controlling flows in devices whose dimensions or internal patterns vary from a few hundred nanometers to a few tens of micrometers arises, this work will be devoted to an analysis and characterization of the flows applied to microsystems. Voir les détails
Mots clés : microfluidics, DNA microarrays, microsystems
Effect of Cu/Ni Ratio on the Chemical composition, Magnetic behaviour, and Structural properties of a FeCuNi based alloy
The aim of this project is to study and understand the influence of copper and nickel concentration on the magnetic, morphological and structural properties of the Fe70Cu30-xNixalloy. The alloy was elaborated by mixing iron, nickel and copper powders by the mechanicalalloying technique for 10 hours of milling. The elements were characterised by different techniques: X-ray diffraction (XRD), Scanning Electron Microscope (SEM) and Vibrating Sample Magnetometer (VSM). The X-ray diffraction study shows that the crystallite size decreases with increasing Ni. When it come to the magnetic properties, the coercivityHc and the saturation moment Ms rise from 83 Oe, 121.5 emu/g to 156 Oe, 140 emu/g respectively. Voir les détails
Mots clés : Fe70Cu30-xNix, Scanning Electron Microscope (SEM), X-ray diffraction
Développement d’un Biomatériau à Base de Polymère etRenfort Végétale
In the last few years, there has been a strong interest in the development of biodegradablepolymers as an alternative for many applications. This is in order to reduce the largeconsumption of plastic causing environmental problems.In this study we develop low cost and low density biodegradable composite materials thatcan be recycled and help to combat the pollution problems of the 21st century. The workdone in this thesis is oriented along this axis and aims to develop mixtures based on polyvinylchloride and fiber Atriplex halimus whose loading rates vary from 1% to 10%. The varioustechniques of characterization were carried out on the developed mixtures. The physicalproperties such as absorption, as well as mechanical, hardness, tensile test, showed animprovement of the content and resistance of our material reinforced by the vegetable fiber.These observations lead us to conclude that such a material can be used on an industrialscale for packaging applications Voir les détails
Mots clés : composite materials, Polyvinyl chloride, Atriplex halimus, Vegetable fiber
Étude et réalisation d'un systèmeembarqué pour leContrôle et l’aide à la navigation d'unquadri-rotors.
This work consists firstly in the realization of an autopilot board for Quad-rotor basedon the ARDUINO MEGA development board. The latter must be able to acquire and processinformation from sensors: MPU6050 (The accelerometer, the gyroscope, the magnetometer)and the GPS sensors in real time to command and control the Quad-rotor. The resultsobtained by the sensors must be displayed on a graphical interface representing the groundstation. The second part is to realize and embark of a navigation aid system based onultrasonic sensors. Voir les détails
Mots clés : Quad-rotor, autopilot, Arduino MEGA, GPS, MPU6050, ground station, real time, Ultrasound
ELABORATION PAR SYNTHÈSE VERTE ET CARACTÉRISATION DES NANOPARTICULES D'OXYDES DE FER ET LEUR APPLICATION ÀL'ADSORPTION DU COLORANT BLEU DE MÉTHYLÈNE
Nanosciences and nanotechnology are the technological and scientific revolution of today, as was microtechnology in 1970-1980. The objective of green synthesis is to minimize, at best, the danger and considerably increase the efficiency of certain chemical practices, particularly at the nano-scale.This work consists first of all in synthesizing iron oxide nanoparticles by the "Green Synthesis" method based on plant extracts and metal salts; then to characterize the nanoparticles produced by different analysis techniques: Fourier Transform Infrared spectroscopy (FTIR), Scanning Electron Microscopy (SEM) associated to Energy Dispersive Spectroscopy (EDS), and X-ray Diffraction (XRD) ); then to use the nanoparticles for the application to the adsorption of the dye (methylene blue). Voir les détails
Mots clés : Nanosciences, Nanotechnology, Microtechnology, X-ray diffraction, Fourier Transform Infrared spectroscopy, Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy
Détermination expérimentalement et numériquement des paramètres de rupture à l'aide de la technique de corrélation d'image digitales DIC et l'analyse FEM
For the purpose of determining the critical fracture parameters of materials such as the critical energy restitution rate GIc, the stress intensity factor KIc, the maximum fracture load and the critical crack opening CTOD where δc numerous approaches are used in the literature. One of the approaches is based on experimental tests assisted by numerical methods such as Digital Images Correlation DIC and FEM finite element analysis. A FEM finite element analysis under a computation code (ABAQUS) allows to simulate the rupture tests, through numerical models in elasticity or elasto-plasticity allows to extract the values of the different components of the displacement and deformation field, the latter are confronted with the same parameters obtained experimentally. And finally, the calculation of the energy restitution rate and the stress intensity factor as well as the critical opening of the CTOD cracks. Voir les détails
Mots clés : Critical failure parameter, The critical energy release rate GIc, The stress intensity factor KIc, The maximum breaking load
Réalisation d'un système de navigation d’un quadricoptère piloté par carte Raspberry Pi
This thesis is devoted to the realization of a navigation system specific to the quadricopter based on the Raspberry Pi 3 B development board. The latter must acquire and process in real time the information from the MPU6050 and GPS sensors, integrate scenes captured by a Pi camera integrated with the system produced, command and control the quadcopter remotely via a joystick and a smartphone. The results obtained by the sensors and the camera to be displayed on the smartphone, which represents the ground station. Voir les détails
Mots clés : UAV, quadricopter, navigation system, Raspberry Pi 3B, MPU6050, GPS, real time, Pi camera, joystick, smartphone.